We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Suzanne
December 10, 2019
How to install the drum belt tensioner
For model number WGD7300XW0
Hello Suzanne, Thank you for the question. There is one screw and a spring attached to the Idler Pulley Wheel and Arm. You just need to unscrew the screw and unhook the spring. Hope this helps!
Was this helpful?
Thank you for voting!
Colleen
June 26, 2023
How do you get access to the dryer drum? Does the front come off or the to somehow?
For model number WGD7300XW0
Hi Colleen, thank you for a very interesting question. You will need to open the door and lift the top with a putty knife. You will need a quarter-inch or a five-sixteenth-inch screwdriver on your screwdriver to remove the screws inside the washer holding the front door panel of the washer. Take off the wire harness that holds the door. Then you will need to remove the four bulkhead screws and two blower housing screws to access the drum. Also, make sure to unclip the moisture sensor in the lower right corner before removing the door panel fully. We hope this information is useful!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Dryer ran but would not heat
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are ... Read more located on top of the gas valve. I borrowed my neighbor"s ohm meter and touched the two probes on the coils terminals to check for continuity and found that one of the coils read zero. I then took both of the coils out by removing two screws and tested each coil again. One coil read 500-850 and the other read zero. This meant that it was no good so I called for the part and received it in three days. I reassembled the parts and turned the dryer on and it fired up after a few seconds. It works as good as new. The part plus shipping was less than $30. My repairman would have charged me $150-$200. While the dryer was apart I gave it a good cleaning with a vacuum and a toothbrush in delicate areas. I also removed and cleaned the lint trap housing by removing two nuts. I didn't know much about gas dryers, but thanks to PartSelect I easily fixed it myself.
Read less
Parts Used:
-
Gary from Haverhill, NH
-
Total Repair Time:
30 - 60 mins
-
Tools:
Nutdriver, Screw drivers, Socket set
395 of 445 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer flame goes out after about 8-minutes from start and won’t work again until a 15-minute rest.
There was no problem with lint build-up within the dryer & the exhaust vent. I removed the gas cycling thermostat & thermal fuse from system & dryer still was not operating correctly. The radiant sensor & hi-limit thermostat both seemed to be operating correctly. That left either of the two coils as the culprits. I replaced both coils ... Read more & the problem was corrected.
Read less
Parts Used:
-
andy from Bethesda, MD
-
Difficulty Level:
Easy
-
Total Repair Time:
30 - 60 mins
-
Tools:
Screw drivers
206 of 228 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
felt strip came off lint screen
ordered new lint screen, removed old screen, inserted new screen.
Parts Used:
-
JEFFREY from FALL RIVER, MA
-
Difficulty Level:
Really Easy
-
Total Repair Time:
Less than 15 mins
221 of 273 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!